HDPE and Microducts

The split sealing element is a universal element that serves as a pipe end before installing the cable and, after installing the cable into the tube, is repeatedly used as a split micro-tubular micro-tubing seal. ; The element allows for pressure-...

Clutch-water gas block 10/8 mm gas tight seals through cable tightening. Home ; You can also save directly into the ground (recommended clutch wrap insulating tape).

Clutch gas-water Block 12/6 mm gas tight seals through cable tightening. Home ; You can also save directly into the ground (recommended clutch wrap insulating tape).

Clutch-water gas block 16/8 mm gas tight seals through cable tightening. Home ; You can also save directly into the ground (recommended clutch wrap insulating tape).

Clutch-water gas block 14/8 mm gas tight seals through cable tightening. Home ; You can also save directly into the ground (recommended clutch wrap insulating tape).

Direct Install thin-walled tubes, for which the typical installation to another outer protective pipe or vacancies in this pipe with indirect exposure to mechanical.

Direct Install thin-walled tubes, for which the typical installation to another outer protective pipe or vacancies in this pipe with indirect exposure to mechanical.

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

The split sealing element is a universal element that serves as a pipe end before installing the cable and, after installing the cable into the tube, is repeatedly used as a split micro-tubular micro-tubing seal. ; The element allows for pressure-...

The split sealing element is a universal element that serves as a pipe end before installing the cable and, after installing the cable into the tube, is repeatedly used as a split micro-tubular micro-tubing seal. ; The element allows for pressure-...

The split sealing element is a universal element that serves as a pipe end before installing the cable and, after installing the cable into the tube, is repeatedly used as a split micro-tubular micro-tubing seal. ; The element allows for pressure-...

The split sealing element is a universal element that serves as a pipe end before installing the cable and, after installing the cable into the tube, is repeatedly used as a split micro-tubular micro-tubing seal. ; The element allows for pressure-...

Quality connectors designed for direct installation. ; Highly resistant to fire, to secure indoor installations ; Parameters: ; ; ; Name ; Value ; ; Material: ; HR polymer ; ; Spring Material: ; stainless steel ; ; Sealin...

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

Foam sponge in the shape of a roller, for tubes ID 4-6 mm is used to clean the microtube before installing the cable. Remove the sponge to remove the microtube of all dirt and moisture. Two sponges can also be used for the application of a lubricant.

Foam sponge in the shape of a roller, for tubes ID 7-9 mm is used to clean the microtube before installing the cable. Remove the sponge to remove the microtube of all dirt and moisture. Two sponges can also be used for the application of a lubricant.

The 7/4mm microtube clutch is used to connect the microt runs. The clutch ensures protection against water and dirt. It is resistant to microfibre blowing. It is not advisable to use it for microtubes stored directly in the ground. Diameter of microtubes: 7 and 4m ...

Foam sponge in the shape of a roller, for tubes ID 7-9 mm is used to clean the microtube before installing the cable. Remove the sponge to remove the microtube of all dirt and moisture. Two sponges can also be used for the application of a lubricant.

The tool for rapidly removing the burrows from the microt runs designed to remove burners from the inside of the microtubes and is ideal for preparing the interior of the optical microt runs for the end.