HDPE and Microducts

Cable grip prevents accidental ejection of nanotubes joints or terminations

Clutch nanotubes 10/8 mm is used to connect micro. Clutch provides protection against water and dirt. It is resistant to pressures in the blowing microfibers. Home ; It is not advisable to use for nanotubes deposited directly into the ground. ; ...

Clutch-water gas block 10/8 mm gas tight seals through cable tightening. Home ; You can also save directly into the ground (recommended clutch wrap insulating tape).

Clutch microducts 12/10 mm is used for connection of microducts. Clutch provides protection against water and dirt. It is resistant to pressures in the blowing microfibers. Home ; It is not advisable to use for nanotubes deposited directly into the gr...

Cable grip prevents accidental ejection of nanotubes coupling or fitting.

Reduction microducts 12/10 mm (8 mm) is used for connecting the micro different diameters. Reduction provides protection against water and dirt. It is resistant to pressures in the blowing microfibers. ; It is not advisable to use for nanotubes depos...

Reduction microducts 14/12 mm (10 mm) is used for connecting the micro different diameters. Reduction provides protection against water and dirt. It is resistant to pressures in the blowing microfibers. Home ; It is not advisable to use for nanotubes ...

Direct Install thin-walled tubes, for which the typical installation to another outer protective pipe or vacancies in this pipe with indirect exposure to mechanical.

Clutch microducts 14/10 mm is used for connection of microducts. Clutch provides protection against water and dirt. It is resistant to pressures in the blowing microfibers. Home ; It is not advisable to use for nanotubes deposited directly into the gr...

Clutch microducts 16/12 mm is used for the connection of microducts. Clutch provides protection against water and dirt. It is resistant to pressures in the blowing microfibers. Home ; It is not advisable to use for nanotubes deposited directly into th...

Clutch microtubes 5/3.5 mm is used to connect micro. Clutch provides protection against water and dirt. It is resistant to pressures in the blowing microfibers. Home ; It is not advisable to use for nanotubes deposited directly into the ground. ...

Clutch microtube 7/3.5 mm is used for connection of microducts. Clutch provides protection against water and dirt. It is resistant to pressures in the blowing microfibers. Home ; It is not advisable to use for nanotubes deposited directly into the gro...

Clutch microtube 7/5.5 mm is used for connection of microducts. Clutch provides protection against water and dirt. It is resistant to pressures in the blowing microfibers. Home ; It is not advisable to use for nanotubes deposited directly into the gro...

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

Jackmoon serves as protection from water and dirt. Is resistant to pressure from blowing microfibers

Cable grip prevents accidental ejection of nanotubes coupling or fitting.

Reduction microducts 10/7 millimeters (5.5 mm) is used for connecting the micro different diameters. Reduction provides protection against water and dirt. It is resistant to pressures in the blowing of microfibres. Home ; It is not advisable to use fo...

Reduction microducts 12/7 millimeters (5.5 mm) is used for connecting the micro different diameters. Reduction provides protection against water and dirt. It is resistant to pressures in the blowing of microfibres. Home ; It is not advisable to use fo...